No. The YN560 III has a radio receiver based on the Yongnuo RF603/RF605/YN560 manual flash only protocol. The Canon 430EX III-RT has a built in radio transmitter and receiver that are based on Canon's RT protocol. The two protocols are not compatible. If you are using the 430EX III-RT in manual flash mode, you can also set the YN-560 III to S1 optical slave mode and the Yongnuo flash will fire when it detects the light from the Canon flash. If you are using the 430EX III-RT in E-TTL mode, you can set the YN-560 III to S2 optical slave mode and the Yongnuo flash should ignore the preflash and fire when it detects the light from the Canon's main flash. This will let you sync the firing of both flashes without any additional gear but technically it does not use the radio transceivers of either flash since the Yongnuo is reacting to the optical output of the Canon flash. As with any time you use optical slave flashes, you may need to lengthen your shutter speed a notch or two below the camera's X-sync speed. The extra time may be needed to allow the circuitry in the optical slave flash to react to the light from the other flash. If you are using the 430EX III-RT or any other RT "Master" on the camera's hot shoe you can attach an YNE3-RX to the shoe of the YN-560III and it will send a properly synced "fire" signal to the YN-560III. The YNE3-RX is a receiver-only trigger for the Canon RT system. When used with a Canon E-TTL capable flash 580EX II, 430EX II, YN-568EX II, etc. it enables the full capability of the flash when using a Canon RT compatible transmitter on the camera. You'll have to make any setting changes for the YN-560III directly on the YN-560III control panel. Since the YN-560III is a manual only flash, of course you can only use it manually. No E-TTL, HSS, 2nd curtain, etc.
UnixDriver Archive. What's a legacy driver? Open source drivers for NVIDIA nForce hardware are included in the standard Linux kernel and leading Linux distributions. This page includes information on open source drivers, and driver disks for older Linux distributions including 32-bit and 64-bit versions of Linux.
Contents Table of Contents Bookmarks Quick Links Related Manuals for Yongnuo YN560-IIIWatches& Wearables. Lowyat.NET's trading platform - a dedicated subforum for you to advertise, buy and sell anything under the sun, from technology products to clothes, new or used. Forum Led by: Moderator, Moderator (Probationary) 500,412. 2,660,302.
Yongnuo YN560 III Manual Flash SpeedliteYongnuo YN560 III is one of the first budget-friendly camera flashes released with a radio receiver built into it. This speedlight is effectively a YN560-II that can be triggered by a Yongnuo RF-602, RF-603 or RF-605 wireless trigger without needing to connect an external receiver. YN560 III can be triggered and controlled by YN560-TX commander as well as by YN560 IV/YN660 is no TTL support in the YN560 III, which has the advantage of making it truly universal, supporting any camera system with a hot-shoe or sync port interface, or even those without, using the built-in optical slave. It’s important to note, however, that these Yongnuo YN-560 series of flashes are manual control only, meaning they don’t offer TTL metering. This means you have to adjust the flash power manually and the flash won’t be able to determine the power of the flash by YN560 III features full tilt functionality, flipping up and down 90 degrees pointing at the subject to pointing upwards vertically. It rotates anti-clockwise 180 degrees and clockwise 90 degrees. It comes with a carry pouch and a flash stand which allows you to stand the flash up on a YN560 III Speedlite features GHz wireless radio receiver. YN560 III is a long range manual flash unit that can be triggered by the RF-603, RF-602, RF-605 wireless transmitters or YN560-TX/YN560 IV/YN660 commander unit. The YN560III is powerful with a guide number of 58m at ISO 100, 105mm. The unit is also quite versatile with a zoom range of 24-105mm, which is able to be expanded to 18mm with the built-in wide-angle diffuser. Additionally, this output can be adjusted from 1/1 to 1/128 power in 1/3 and 1/2 EV bounce and swivel lighting is possible due to -7 to 90° tilt and 270° of rotation with the locking flash head. The flash can also be triggered optically with either instant sync or skip pre-flash options for simpler off-camera firing. A built-in PC sync port further enhances the flash’s connectivity and a Multi mode allows for stroboscopic lighting effects. The flash runs on 4 AA batteries and has a recycle time of about 3 YN560 III FeaturesPowerful operation with Guide number 58 meters at ISO 100, slave mode allows the speedlite to be triggered by YN560 IV/ YN660 flash speedlites, YN560-TX, RF-602, RF-603, RF-603 II and hot shoe, solid and stroboscopic mode of up to 8 flashes per second power must be 1/8 or lower as well as Manual, S1 and S2 optical slave sound prompt lets you know when the flash is power pack socket – Canon plug compatible with Yongnuo SF-18C and SF-17C external battery wide angle diffuser and bounce temperature is save of flash current LCD screen and improved button design for quick change of flashes with one set of Sync seconds for full power flash protection and power saving with all cameras with standard Hot Shoe interface – Canon, Nikon, Pentax, Olympus, Fuji and some Sony designInsulated Gate Bipolar Transistor IGBTGuide 58 meters ISO 100, 105mmFlash modeManual, MULTITriggering ModeSet-top, wireless slave mode, S1, S2 optical slave modesWireless triggering distanceup to 100m wireless; 20-25m indoor, 10-15m outdoor optical controlZoom range20, 24, 28, 35, 50, 70, 80, 105mmVertical rotation angle-7~90 degreesHorizontal rotation angle0~270 degreesPower supply4×AA size batteries Alkaline or Ni-MH are supportedLighting times100~1500 times AA alkaline cell usedRecycle timeapprox 3s AA alkaline cell used at full powerColor temperature5600kFlash duration1/200s~1/20000sFlash control8 levels of output control 1/128~1/1, 29 levels of fine tuningExternal interfacehot shoe, external HV battery port, PC sync portAdditional featuresSecond-curtain sync, manual zoom, sound prompt, advanced setting, automatically saving setting, PC port, power saving mode and over heat x x / x x mmNet weight350gCompatible withYongnuo YN560 III is compatible with all Canon, Nikon, Pentax, Olympus, Panasonic DSLR Cameras, basically any camera with standard hot shoe some Sony models also. Yongnuo RF-605, RF-603 I/II, RF-602, YN622C, YN622C II, YN622N, YN622N II, YN560-TX Yongnuo YN-560 IV, includesYongnuo YN560 III speedliteMini StandManualOriginal boxProtection bag LimitlessIntegrations. OneSignal integrates with leading analytics, CMS, and eCommerce solutions including Amplitude, Mixpanel, Segment, HubSpot, Shopify, WordPress, and many more. Sync audiences and user data to trigger real-time messages. With more than 60 owned and operated sports sites, the USA Today Sports Media Group relies on OneSignal I have two Canon bodies, three flashes, and two RF-603II triggers. I am planning to set the Yongnuo YN-560III as an off-camera flash at an event. The Yongnuo 560 III has its built-in RF-603 receiver. I know that I can hook up one RF-603II trigger on my first body with another on-camera flash to trigger the Yongnuo 560 III remotely. But can I also use the second RF-603II trigger on my second body to trigger this Yongnuo YN-560III flash as well with same channel setting? Can I switch to take the photo with a different body but trigger the same off-camera flash? gold badges87 silver badges148 bronze badges asked Sep 17, 2015 at 1747 As long as the channel and group settings are selected the same way on all three pieces of equipment you should be able to use either camera/transceiver to trigger the receiver in the off camera YN-560 III. answered Sep 17, 2015 at 2037 Michael CMichael C173k10 gold badges204 silver badges550 bronze badges